🌝 How To Tension A Serpentine Belt

For More Info visit us at: http://1aau.to/h/b8S/The tensioner is a springed device that keeps the serpentine belt in your vehicle at the correct tension to k Replacement of serpentine belt tensioner and serpentine belt on a 2006 Honda Ridgeline with a 3.5L v6.Due to factors beyond the control of CharlesAndCars, it step 1 :Removing the Wheel. 0:25. Loosen the 21mm lug nuts with the vehicle on the ground. Raise the vehicle with a floor jack. Secure the vehicle on jack stands. Remove the lug nuts. Remove the hub cap. Pull off the wheel. step 2 :Removing the Serpentine Belt. An adjustment bolt on the alternator provides belt tension on Toyota's 1.8L engine. This belt is easier to replace than many, but does require that the alternator mounts are loosened up. This engine was used from 2009 to 2013 and is also found on the Yaris, Matrix, Scion xD and Pontiac Vibe. Shown is a 2010 Toyota Corolla. The job at a glance On the passenger's side of the engine, place your 15mm wrench or ratchet/breaker bar with a 15mm socket on the belt tensioner bolt. Turn the tensioner clockwise as if tightening the bolt to release tension on the belt. While holding the tensioner away from the belt with one hand, slide the loosened belt off of the tensioner pulley. In this video I cover a serpentine belt installation and how to overcome the spring tension of the belt tensioner. To tighten the belt, simply loosen the tensioner pulley bolt and turn the pulley clockwise. Then, retighten the bolt and check the pulley again to make sure it’s not moving. If you keep an eye on your serpentine belt and make sure it’s tight, you’ll be able to avoid any serious engine problems down the road. Step 3 – Remove serpentine belt. Remove the serpentine belt by turning the 19mm bolt on the tensioner clockwise. It is easiest to access this bolt from the engine bay as shown in Figure 3. After the tension is released, you can maneuver the belt out of the engine bay. Figure 3. The serpentine belt in your car powers the accessories such as air conditioning, power steering, the Learn how to fix a squeaky tensioner pulley in your car. Remove the old serpentine belt tensioner pulley and set it aside. step 3 :Install the new serpentine belt tensioner. 1:47. Mount your tensioner pulley. Use your 13 mm socket and ratchet to secure the new serpentine belt tensioner from 1A Auto. step 4 :Install the serpentine belt. 2:26. Find out the steps for removing and replacing the AC compressor belt and the serpentine belt tensioner on the 05-14 Volkswagen Jetta with this how-to video. step 1 :Removing the Wheel. 0:33. Loosen the lug bolt covers with a pick. Loosen one of the lug bolts with a key found by the spare tire. Loosen the 17mm lug bolts with the vehicle on the Step 3 – Remove tension on the serpentine belt. On the 3.8L V6, the drive belt tensioner is composed of a pulley and a swing arm. A 3/8-inch socket wrench is sufficient to release the tension on the drive belt. Insert the socket wrench drive shaft into the center square hole, and turn the wrench clockwise. Step 2 – Remove the serpentine belt. Place your 19mm socket on the tensioner nut located above the tensioner pulley. Figure 4. Tensioner pulley nut. While turning the socket clockwise (toward the front of the car), slide the belt off of one of the pulleys. By pulling the nut, you are releasing the tension on the belt. That said, many owners here replace the serpentine belt at around 100K miles/10 years. As a new owner, its your call if a new one helps you sleep at night. If you DO replace it, buy a Serpentine Belt Tensioner Tool, make the job easier than interlocking several box wrenches together for leverage! Now, you're going to use a serpentine belt tool. We're going to use the 15-millimeter adapter on the end of it. If you don't have one, you can just use a 15-millimeter wrench. Just be careful. Loosen up the tension on it as if you're turning it clockwise. And then over on the idler, just take the belt off. Release the tensioner. Pull off your tool. TnYsa.

how to tension a serpentine belt